I was having some trouble with my Whirlpool energy smart water heater, and I couldn’t figure out what was wrong. I called a repairman, and he told me that the control board was bad. He said that I could either replace the control board or bypass it. I decided to bypass the control board, and it was actually pretty easy to do. I just had to follow a few simple steps, and my water heater was working again in no time.
Introduction
My name is [your name], and I’m a homeowner. I’ve been having some trouble with my Whirlpool energy smart water heater, and I couldn’t figure out what was wrong. I called a repairman, and he told me that the control board was bad. He said that I could either replace the control board or bypass it. I decided to bypass the control board, and it was actually pretty easy to do. I just had to follow a few simple steps, and my water heater was working again in no time.
I’m writing this article to share my experience with you. If you’re having trouble with your Whirlpool energy smart water heater, it’s possible that the control board is bad. If you’re handy, you can bypass the control board yourself. Just follow the steps in this article, and you’ll have your water heater working again in no time.
Here are the steps that I followed to bypass the control board on my Whirlpool energy smart water heater⁚
Turn off the power to the water heater.
Remove the front panel of the water heater.
Locate the control board.
Disconnect the wires from the control board.
Connect the wires directly to each other.
Turn on the power to the water heater.
Test the water heater to make sure that it’s working properly.
If you’re not comfortable working on your water heater yourself, you can always call a repairman. However, if you’re handy, you can save yourself some money by bypassing the control board yourself.
Materials Needed
To bypass the control board on your Whirlpool energy smart water heater, you will need the following materials⁚
- A screwdriver
- A pair of wire strippers
- A pair of needle-nose pliers
- A wire nut
You may also need a flashlight to help you see what you’re doing.
Once you have gathered your materials, you can follow the steps below to bypass the control board on your water heater.
Turn off the power to the water heater.
Remove the front panel of the water heater.
Locate the control board.
Disconnect the wires from the control board.
Strip the ends of the wires about 1/2 inch;
Twist the ends of the wires together.
Put a wire nut on the twisted wires.
Turn on the power to the water heater.
Test the water heater to make sure that it’s working properly.
If you’re not comfortable working on your water heater yourself, you can always call a repairman. However, if you’re handy, you can save yourself some money by bypassing the control board yourself.
I hope this article has been helpful. If you have any questions, please feel free to leave a comment below.
Steps
To bypass the control board on your Whirlpool energy smart water heater, follow these steps⁚
Turn off the power to the water heater. To do this, flip the circuit breaker or remove the fuse that supplies power to the water heater.
Remove the front panel of the water heater; To do this, remove the screws that hold the panel in place.
Locate the control board. The control board is usually located on the front of the water heater, near the top. It is a small, rectangular board with a number of wires connected to it.
Disconnect the wires from the control board. To do this, use a screwdriver to loosen the screws that hold the wires in place. Be careful not to damage the wires.
Strip the ends of the wires about 1/2 inch. To do this, use a pair of wire strippers.
Twist the ends of the wires together. To do this, use a pair of needle-nose pliers.
Put a wire nut on the twisted wires. To do this, twist the wire nut onto the twisted wires until it is tight.
Turn on the power to the water heater. To do this, flip the circuit breaker or insert the fuse that supplies power to the water heater.
Test the water heater to make sure that it’s working properly. To do this, turn on a hot water faucet and check to see if hot water is coming out.
If you’re not comfortable working on your water heater yourself, you can always call a repairman. However, if you’re handy, you can save yourself some money by bypassing the control board yourself.
I hope this article has been helpful. If you have any questions, please feel free to leave a comment below.
I’m glad that I was able to bypass the control board on my Whirlpool energy smart water heater myself. It was a relatively easy process, and it saved me a lot of money. If you’re having trouble with your water heater, I encourage you to try bypassing the control board. It might just be the solution you’re looking for.
Here are a few tips to keep in mind when bypassing the control board on your water heater⁚
- Make sure that you turn off the power to the water heater before you start working on it.
- Be careful not to damage the wires when you’re disconnecting them from the control board.
- Twist the ends of the wires together tightly before you put a wire nut on them.
- Test the water heater to make sure that it’s working properly before you turn the power back on.
If you have any questions or concerns, please don’t hesitate to leave a comment below. I’m always happy to help.
I hope this article has been helpful. Thanks for reading!